Effect of storage time and temperature on hydrogen fermentation of food waste

Practically, before being fed to the treatment plant, food waste (FW) is stored for up to a week in a storage tank under ambient temperature condition, which would have an impact on the bioenergy yield. In the present work, FW was stored at different temperatures (5 °C, 20 °C, and 35 °C) for 0 d, 1 d, and 2 d, and it was used as a feedstock for mesophilic H₂ fermentation. H₂ production curves were divided by three groups, finally attaining 1.7–1.8 mol H₂/mol hexose_added, 1.4–1.5 mol H₂/mol hexose_added, and 1.2 mol H₂/mol hexose_added, achieved from the (fresh, FW stored at 5 °C), (FW stored at 20 °C, and 35 °C for 1 d), and (FW stored at 35 °C for 2 d), respectively. The different performance was attributed to the growth of indigenous lactic acid bacteria such as Lactobacillus and Weissella during storage under high temperature condition. In addition, it was found that the activity of homoacetogenic reaction (R17, 4H₂ + CO₂ → Acetate) calculated by establishing metabolic flux balance was different depending on the H₂ production performance. The flux of R17 ranged 0.03–0.06 under low H₂ yield achieved conditions, while it increased to 0.10–0.17 those showing low H₂ yields.     

不同润湿表面液体沸腾的分子动力学模拟

采用分子动力学方法研究纳米尺度下液氩在过热基板上的沸腾过程。通过调节固液间相互作用的方式改变壁面润湿性，模拟并分析了壁面润湿性对沸腾过程中能量传递和液体运动情况的影响。结果表明：不同润湿性表面均会发生固液分离的现象，但是固体表面附近吸附的氩原子数密度随润湿性增强而增大；润湿性较强时，液体的能量上升快，热通量高，液体内部温度梯度大，发生固液分离时间早，系统中氩的温度和能量低，上升过程中液氩密度、厚度变化小；润湿性较弱时，液体的能量上升慢，热通量小，液体内部温度梯度小，发生固液分离时间延后，系统中氩的温度、能量更高，上升过程中液氩密度、厚度变化较大。下部气体压力整体上大于上部气体压力，发生固液分离时润湿性越强的表面上液体上下压差越大，首次上升过程能达到的高度越高，所需时间越短。     

Soret and Dufour effects between two rectangular plane walls with heat source/sink

This study addresses the thermo‐diffusion and the diffusion‐thermo phenomena in a semi‐infinite absorbent channel whose walls are contracting/expanding, with heat source/sink effects. The governing partial differential equations with suitable boundary conditions are transformed to a system of dimensionless ordinary differential equations. An analytic solution of the problem has been found using a technique called homotopy analysis method (HAM). HAM gives consistently valid answers to the problem over an extensive variety of parameters and also provides better accuracy. To validate the analytical results, a comparison has been presented with a numerical solution calculated by using the parallel shooting method. The effects of dimensionless parameters, that is, deformation parameter, Reynolds number, Soret and Dufour numbers, and heat source/sink parameter on the expressions of velocity, temperature, and concentration profiles are analyzed graphically to understand the physics of the deformable channel. It has been noted that the velocity across the channel is higher for the expanding channel, as compared to that for the contracting channel. Also the Soret and Dufour number increases the temperature of the fluid, and decreases the concentration. The temperature profile has an increasing behavior in the case of heat source, and a decreasing behavior in the case of heat sink.     

Adomian decomposition method for the MHD flow of a viscous fluid with the influence of dissipative heat energy

An investigation is carried out on the effect of dissipative heat energy on the flow of an electrically conducting viscous fluid past a shrinking sheet. Both viscous and Joule dissipation effects are considered along with heat generation/absorption for the enhancement of heat transfer properties. The governing nonlinear coupled partial differential equations are transformed into nonlinear ordinary differential equations by a suitable choice of similarity transformations. However, the complex transformed equations are solved by an approximate analytical method known as the Adomian decomposition method with a suitable initial guess solution assumed from the known initial conditions. Moreover, the behavior of several parameters characterizing the flow phenomena are studied via graphs and the numerical computations for the engineering coefficients are obtained and presented through tables. However, the major outcomes of the results are that a higher suction is required to resist the fluid temperature and sinks as well as the dissipative heat energy favors enhancing the fluid temperature at all points in the flow domain.     

Development of mobile miniature natural gas liquefiers

With increasing consumption of natural gas (NG), small NG reservoirs, such as coalbed methane and oil field associated gas, have recently drawn significant attention. Owing to their special characteristics (e.g., scattered distribution and small output), small-scale NG liquefiers are highly required. Similarly, the mixed refrigerant cycle (MRC) is suitable for small-scale liquefaction systems due to its moderate complexity and power consumption. In consideration of the above, this paper reviews the development of mobile miniature NG liquefiers in Technical Institute of Physics and Chemistry (TIPC), China. To effectively liquefy the scattered NG and overcome the drawbacks of existing technologies, three main improvements, i.e., low-pressure MRC process driven by oil-lubricated screw compressor, compact cold box with the new designed heat exchangers, and standardized equipment manufacturing and integrated process technology have been made. The development pattern of “rapid cluster application and flexible liquefaction center” has been eventually proposed. The small-scale NG liquefier developed by TIPC has reached a minimum liquefaction power consumption of about 0.35 kW·h/Nm³. It is suitable to exploit small remote gas reserves which can also be used in boil-off gas reliquefaction and distributed peak-shaving of pipe networks.     

Efficiency and effectiveness enhancement of an intercooler of two‐stage air compressor by low‐cost Al2O3/water nanofluids

The present study was aimed to utilize low‐cost alumina (Al₂O₃) nanoparticles for improving the heat transfer behavior in an intercooler of two‐stage air compressor. Experimental investigation was carried out with three different volume concentrations of 0.5%, 0.75%, and 1.0% Al₂O₃/water nanofluids to assess the performance of the intercooler, that is, counterflow heat exchanger at different loads. Thermal properties such as thermal conductivity and overall heat transfer coefficient of nanofluid increased substantially with increasing concentration of Al₂O₃ nanoparticles. Specific heat capacity of nanofluids were lower than base water. The intercooler performance parameters such as effectiveness and efficiency improved appreciably with the employment of nanofluid. The efficiency increased by about 6.1% with maximum concentration of nanofluid, that is, 1% at 3‐bar compressor load. It is concluded from the study that high concentration of Al₂O₃ nanoparticles dispersion in water would offer better heat transfer performance of the intercooler.     

地埋管换热器分区运行对土壤热堆积特性影响的研究

为了缓解埋管区域土壤的热量堆积问题,提出了埋管换热器按内中外、块状、间隔三种分区运行的策略,利用CFD软件建立了10×10的井群换热模型,对地源热泵系统在三种分区与不分区运行策略下运行十年进行数值模拟,分析不同分区运行策略对土壤温度分布和土壤热堆积特性的影响。模拟结果可知:不分区、内中外分区、块状分区、间隔分区四种运行策略下埋管区域的平均温度分别为25.23、23.31、23.06、23.28℃,最高温度分别为40.62、32.77、40.65、38.93℃;分区运行较不分区运行可以有效缓解热堆积作用,埋管区域整体温度较不分区运行时降低了2.00℃左右,内中外分区策略可以显著缓解埋管区域热堆积。     

Optimization of three-dimensional boiling enhancement structure at evaporation surface for high power light emitting diode

A theoretical model of phase change heat sink was established in terms of thermal resistance network. The influence of different parameters on the thermal resistance was analyzed and the crucial impact factors were determined. Subsequently, the forming methods including ploughing–extrusion and stamping method of boiling enhancement structure at evaporation surface were investigated, upon which three-dimensional microgroove structure was fabricated to improve the efficiency of evaporation. Moreover, the crucial parameters related to the fabrication of miniaturized phase change heat sink were optimized. The heat transfer performance of the heat sink was tested. Results show that the developed phase change heat sink has excellent heat transfer performance and is suitable for high power LED applications.     

太阳能及空气源热泵复合供热系统故障诊断研究与应用

为确保复杂太阳能热水系统的稳定运行,有必要采集实时运行数据从中获取故障特征信号,通过专家系统进行自动故障诊断。采用故障树分析方法,以太阳能热利用系统典型故障为例构建故障树,求解最小割集,并以此为基础建立诊断知识库;运用正向推理结合人工辅助决策机制进行故障诊断和定位,建立故障诊断专家系统。开发故障诊断软件,并在工程中进行测试,验证故障辨识的准确性。     

Heat Transfer Analysis of MHD Power Law Nano Fluid Flow through Annular Sector Duct

Flow and heat transfer analysis of an electrically conducting MHD power law nano fluid is carried out through annular sector duct,under the influence of constant pressure gradient.Two types of nano particles(i.e.Cu and TiO2)are used in power law nano fluid.Strongly implicit procedure,(SIP)is used to simulate the discretized coupled algebraic equations.It has been observed that volume fraction of nano particles,ϕand magnetic field parameter,Ha are favourable for the heat transfer rate,however,both resist the fluid flow.Impact of applied uniform transverse magnetic field exceeds in the case of shear thickening fluids(i.e.n>1)by increasing the value of Ha as compared to that in shear thinning fluids(i.e.n<1).Therefore,enhancement in heat transfer rate is comparably more in shear thickening fluid.Furthermore,comparable limiting case study with published result is also carried out in this research paper.